English
Pусский
Français
Portugues
Español
العربية
lingua italiana
日本語
한국어
Türk dili
Bei der Auswahl eines Ringkerntransformators die Leistung des Ringkerntransformators Transformator sollte basierend auf der Spannung und dem Stromverbrauch der Last bestimmt werden. Der Nennausgangsstrom eines Ringkerns Transformator is the output current at full load. When overloaded, the toroidal Transformator can output more than 30% of the rated current. The overload capacity of toroidal Transformators is very good, but the following two points need to be noted.
1. Wird verwendet, um überlastete Maschinen und Geräte zu starten
The current of some devices is rated during operation, but the current at startup is very large, sometimes exceeding 30%~50% of the rated current. For example, the overload capacity of an AC servo motor is usually designed to be 3 times the rated operating current. When the load starts, the current is large, which requires the toroidal Transformator to be overloaded for a short time. Such a device with overloaded driving current is equipped with a toroidal Transformator, and the rated output current of the Transformator needs to be considered to exceed about 20% of the rated current of the device. Due to frequent start-up overloads, the temperature of the toroidal Transformator rises, and the long-term Transformator life becomes shorter.
2. Geeignet für Geräte ohne Überlastung
Many devices are designed with the maximum operating current in mind and the startup current does not need to be overloaded. For example, stepper motors are used as equipment power, and the operating current is the same as the starting current. When selecting a toroidal Transformator, it is not necessary to design a margin for the output current of the toroidal Transformator as long as the output current is equal to or greater than 10% of the maximum current of the stepper motor driver. Stepper motors never have overload current. In more work environments, the power of stepper motors is variable. This requires that voltage and current parameters should be determined during structural design, and reasonable power should be given artificially. In fact, the power of aBei der Auswahl eines Ringkerntransformators die Leistung des Ringkerntransformators Transformator should be determined based on the voltage and current usage of the load.
1. Wird verwendet, um überlastete Maschinen und Geräte zu starten
The current of some devices is rated during operation, but the current at startup is very large, sometimes exceeding 30%~50% of the rated current. For example, the overload capacity of an AC servo motor is usually designed to be 3 times the rated operating current. When the load starts, the current is large, which requires the toroidal Transformator to be overloaded for a short time. Such a device with overloaded driving current is equipped with a toroidal Transformator, and the rated output current of the Transformator needs to be considered to exceed about 20% of the rated current of the device. Due to frequent start-up overloads, the temperature of the toroidal Transformator rises, and the long-term Transformator life becomes shorter.
2. Geeignet für Geräte ohne Überlastung
Many devices are designed with the maximum operating current in mind and the startup current does not need to be overloaded. For example, stepper motors are used as equipment power, and the operating current is the same as the starting current. When selecting a toroidal Transformator, it is not necessary to design a margin for the output current of the toroidal Transformator as long as the output current is equal to or greater than 10% of the maximum current of the stepper motor driver. Stepper motors never have overload current. In more work environments, the power of stepper motors is variable. This requires that voltage and current parameters should be determined during structural design, and reasonable power should be given artificially. In fact, the power of aBei der Auswahl eines Ringkerntransformators die Leistung des Ringkerntransformators Transformator should be determined based on the voltage and current usage of the load.
