English
Pусский
Deutsch
Français
Portugues
Español
العربية
lingua italiana
한국어
Türk dili
会社のニュース | | | | | | | | コモンモードチョーク | | | | | | | | 業界ニュース | | | | | | | | 変成器| | | | | | | |RJ45 connectors
を選択するとき フィルター、最も重要な 3 つのパラメータは、定格電流、定格電圧、カットオフ周波数です。
(1) The rated current refers to the working current flowing through the フィルター. When the operating current of the power line フィルター exceeds the rated current, it will not only cause the フィルター to overheat, but also cause the low-frequency フィルターing performance of the フィルター to decrease. This is because the inductance in the フィルター will saturate in the case of a large current, which will reduce the actual inductance. Therefore, it is very necessary to leave a certain margin when determining the rated working current of the フィルター. Generally, the rated current value of the フィルター should be 1.5 times the actual current value.
(2) Determination of rated voltage. If the wires to be フィルターed will not be impacted by high voltages such as electrostatic discharge, electromagnetic pulse, surge, etc., the working voltage of the circuit is the rated working voltage of the フィルター. If this is not the case, for example, the cables dragged outside the equipment will be impacted by high voltage, and this situation needs to be fully considered and sufficient margin is left.
(3) Determination of cut-off frequency. The selection of the cutoff frequency must ensure that the passband of the フィルター covers the bandwidth of the functional signal, ensure the normal operation of the device, and フィルター out unnecessary high-frequency interference to the greatest extent possible. For analog signals, the cutoff frequency is well defined, as long as the cutoff frequency is greater than the bandwidth of the signal. For digital pulse signals, the cutoff frequency can be set to 1/lr, where tr is the rise/fall time of the pulse. If it is a periodic pulse signal, 15 times the pulse repetition frequency can also be taken as the cut-off frequency.
を選択するとき フィルター、最も重要な 3 つのパラメータは、定格電流、定格電圧、カットオフ周波数です。
(1) The rated current refers to the working current flowing through the フィルター. When the operating current of the power line フィルター exceeds the rated current, it will not only cause the フィルター to overheat, but also cause the low-frequency フィルターing performance of the フィルター to decrease. This is because the inductance in the フィルター will saturate in the case of a large current, which will reduce the actual inductance. Therefore, it is very necessary to leave a certain margin when determining the rated working current of the フィルター. Generally, the rated current value of the フィルター should be 1.5 times the actual current value.
(2) Determination of rated voltage. If the wires to be フィルターed will not be impacted by high voltages such as electrostatic discharge, electromagnetic pulse, surge, etc., the working voltage of the circuit is the rated working voltage of the フィルター. If this is not the case, for example, the cables dragged outside the equipment will be impacted by high voltage, and this situation needs to be fully considered and sufficient margin is left.
(3) Determination of cut-off frequency. The selection of the cutoff frequency must ensure that the passband of the フィルター covers the bandwidth of the functional signal, ensure the normal operation of the device, and フィルター out unnecessary high-frequency interference to the greatest extent possible. For analog signals, the cutoff frequency is well defined, as long as the cutoff frequency is greater than the bandwidth of the signal. For digital pulse signals, the cutoff frequency can be set to 1/lr, where tr is the rise/fall time of the pulse. If it is a periodic pulse signal, 15 times the pulse repetition frequency can also be taken as the cut-off frequency.
